C3AR / C3a Receptor (C3AR1) Antibody – Rabbit Polyclonal

Polyclonal

Rabbit

Human
Predicted Reactivity: Monkey

PBS, 0.1% sodium azide.

Immunoaffinity Purified

1 mg/ml (lot specific)

Human C3a Receptor. BLAST analysis of the peptide immunogen showed no homology with other human proteins, except ADRA1A (40%).

Aliquot and store undiluted at -20°C or below for up to 1 year. Can be stored undiluted at 4°C for up to 1 month. Avoid freeze-thaw cycles.

605246

ModBase 3D Structure for Q16581

C3AR/C3a Receptor

GPCR/Anaphylatoxin

C3AR/C3a Receptor antibody was raised againt Human.

Synthetic peptide

C3AR / C3a Receptor antibody was raised against synthetic 20 amino acid peptide from 2nd extracellular domain of human C3a Receptor. Percent identity with other species by BLAST analysis: Human (100%); Gorilla, Marmoset (95%); Orangutan, Gibbon (90%).

Extracellular Domain

Due to the highly specific nature of antibodies and antigens, we cannot predict or be held responsible with respect to how this antibody will behave in your systems. Researchers using this antibody should conduct optimization studies to achieve the most optimal result possible for their intended application.

The following protocol is a recommendation only, and MyBioSource, Inc. makes no guarantee of the results:

Tissue Preparation:
Formalin fixation and embedding in paraffin wax.

Tissue Sectioning:
Make 4-um sections and place on pre-cleaned and charged microscope slides. Heat in a tissue-dryingoven for 45 minutes at 60°C.

Deparaffinization:
Wash dry slides in 3 changes of xylene - 5 minutes each @ RT

Rehydration:
Wash slides in 3 changes of 100% alcohol - 3 minutes each @ RT
Wash slides in 2 changes of 95% alcohol - 3 minutes each @ RT
Wash slides in 1 change of 80% alcohol - 3 minutes @ RT
Rinse slides in gentle running distilled water - 5 minutes @ RT

Antigen retrieval:
Steam slides in 0.01 M sodium citrate buffer, pH 6.0 at 99-100°C - 20 minutes
Remove from heat and let stand at room temperature in buffer - 20 minutes
Rinse in 1X TBS with Tween (TBST) -1 minute @ RT

Immunostaining:
(Do not allow tissues to dry at any time during the staining procedure)
Apply a universal protein block - 20 minutes @ RT
Drain protein block from slides, apply diluted primary antibody - 45 minutes @ RT
Rinse slides in 1 X TBST - 1 minute @ RT
Apply a biotinylated secondary antibody appropriate for the primary antibody - 30 minutes @ RT
Rinse slides in 1X TBST -1 minute @ RT
Apply alkaline phosphatase streptavidin - 30 minutes @ RT
Rinse slides in 1X TBST -1 minute @ RT
Apply alkaline phosphatase chromogen substrate - 30 minutes @ RT
Wash slides in distilled water - 1 minute @ RT

Dehydrate:
(This method should only be used if the chromogen substrate is alcohol insoluble (e.g. Vector Red, DAB)
Wash slides in 2 changes of 80% alcohol - 1 minute each @ RT
Wash slides in 2 changes of 95% alcohol - 1 minute each @ RT
Wash slides in 3 changes of 100% alcohol - 1 minute each @ RT
Wash slides in 3 changes of xylene - 1 minute each @ RT
Apply coverslip

During shipment,small volumes of product will ocassionally become entrapped in the seal of the product vial. We recommend briefly centrifuging the vial to dislodge any liquid in the container's cap prior to opening.

This reagent may contain sodium azide. The chemical, physical, and toxicologial properties of this material have not been thoughly investigated.Standard Laboratory Practices should be followed. Avoid skin and eye contact,inhalation, and ingestion. Sodium azide forms hydrazoic acid under acidic conditions and may react with lead or copper plubing to form highly explosive metal azides. On disposal, flush with large volumes of water to prevent accumulation.

Family: GPCR; Subfamily: Anaphylatoxin